FANDOM


Topbot was a robot that competed in Series 7 of Robot Wars. It came from Team Monad, and was the third robot from the Dublin-based team. Topbot lost in the first round of its heat after the disc broke off, and also lost its qualifier battle in the Third World Championship, where it represented the Republic of Ireland.

Team Monad previously competed in Series 5 with Monad and in Series 6 with 4x4, both of which also failed to win a battle.

DesignEdit

Topbot

Topbot enters the arena inverted

Topbot's weapon was a horizontal spinning disc that was 64cm wide and weighed 30 kilograms, made from steel and aluminum with two hardened teeth. The body had four wheels on top and bottom, making it an invertible robot, and it had a low ground clearance. It was one of the many robots over the weight limit, so there were many small holes drilled in the top and sides of its bodywork to fit the constraints. The disc made the robot quite top-heavy, but made up for it in its power; it smashed the arena wall in its World Championship qualifier battle.

Robot HistoryEdit

Series 7Edit

Topbot vs R.O.C.S. vs Raging Knightmare vs The Executioner

Topbot loses its disc

Topbot received a reasonable draw in Round 1 of the Seventh Wars, against veterans Raging Knightmare, as well as R.O.C.S. and The Executioner. In the opening seconds, it spun around in circles to ward off attacks whilst the disc gained speed. It then charged into the fray, hacking at the rear of R.O.C.S., but a sudden impact with The Executioner's vertical spinning weapon caused Topbot's spinning disc to detach and fly across the arena floor.

Topbot pit

Topbot dangerously skirts along the lip of the pit

Topbot drove around the arena erratically, almost falling in the pit with a wheel hanging over the edge. Topbot then drove into Mr. Psycho's CPZ and was cornered. The House Robot hit Topbot with his hammer, and rather comically, his head fell off. Topbot appeared to break down towards the end of the fight and was pushed by Raging Knightmare onto the flame pit as the time expired and the match went to a judges' decision, who eliminated Topbot from the competition.

Topbotwc3

Topbot takes a lump out of the arena wall

Topbot returned for the Third World Championship, fighting against the South African Crushtacean in its qualifier, which was broadcast as part of Heat G. This time, Topbot entered the arena with its disc face up. Topbot tried to spin up in circles to allow its disc to gain speed, but Crushtacean covered the distance between the pair quickly and prevented Topbot from spinning, shoving it into a CPZ.
Crushtacean vs Topbot

Topbot is pitted by Crushtacean

Topbot escaped, attacking the side of Crushtacean. Topbot slammed into the arena wall, cracking pieces of it before being seized by the crab-like robot and shoved away. Crushtacean pushed Topbot into the pit release, before shoving it down the pit and eliminating it from the competition.
"Topbot, more like Flopbot!"
Craig Charles on Topbot's loss.

ResultsEdit

TOPBOT - RESULTS
Series 7
The Seventh Wars - UK Championship
Heat, Round 1
Heat N, Round 1 vs. Raging Knightmare, R.O.C.S., The Executioner Eliminated
The Third World Championship
Representing Republic of Ireland, Qualifier
Qualifier vs. Crushtacean (RSA) Lost

Wins/LossesEdit

  • Team Monad with Topbot
  • Topbot, without its top armour, in the pits
  • Topbot after Series 7
  • Wins: 0
  • Losses: 2

Series RecordEdit

Series Topbot Record
The First Wars Did not enter
The Second Wars Did not enter
The Third Wars Did not enter
The Fourth Wars Did not enter
The Fifth Wars Entered with Monad
The Sixth Wars Entered with 4x4
The Seventh Wars Heat, Round 1
Series 8 Did not enter
Series 9 Did not enter

TriviaEdit

  • Topbot was the only robot from either part of Ireland to feature in Series 7.

Ad blocker interference detected!


Wikia is a free-to-use site that makes money from advertising. We have a modified experience for viewers using ad blockers

Wikia is not accessible if you’ve made further modifications. Remove the custom ad blocker rule(s) and the page will load as expected.